永利总站ylzz欢迎你_主站

您好,欢迎光临莱州聚峰机械有限公司官方网站!

服务热线

400-879-1999

你所在位置: 首页 >> 新闻资讯 > 行业资讯 >
行业资讯

永利总站ylzz欢迎你“啃胎”有几个技巧应对

来源:/ 时间:2022-06-08

“啃胎”是指一个或多个轮胎的内侧或外侧出现异常加速磨损。与其他轮胎相比,一个轮胎的某一部分磨损得很快。在这种情况下不要担心。这里有几个小贴士可以帮助你。
"Tire gnawing" means abnormal accelerated wear on the inside or outside of one or more tires. A part of a tyre wears out faster than other tyres. Don't worry in this case. Here are a few tips to help you.
检查永利总站ylzz欢迎你_主站气压是否过低或轮胎质量是否合格标准。
Check whether the air pressure of the full-automatic concrete mixer is too low or whether the tire quality meets the standard.
检查轮胎轮辋是否不圆,并做动平衡。
Check whether the tire rim is not round and make dynamic balance.
检查前束尺寸,转向杆球头是否松动,转向器固定螺钉是否松动。
Check the toe in size, whether the steering rod ball joint is loose, and whether the steering gear fixing screw is loose.
检查转向轴主轴或承压轴承是否磨损、严重变形或损坏。
Check whether the steering shaft main shaft or pressure bearing is worn, severely deformed or damaged.
后轮胎面不规则磨损。解决方法:检查钢圈、轮毂螺钉、轴头螺钉是否松动。检查制动毂是否不圆。检查弹簧板和弓形夹固定螺钉是否松动。
Irregular wear of rear tire tread. Solution: check whether the steel ring, hub screw and shaft head screw are loose. Check whether the brake hub is not round. Check whether the spring plate and bow clamp fixing screws are loose.

永利总站ylzz欢迎你_主站

经常检查胎压,查看胎面磨损情况。
Check the tire pressure frequently and check the tread wear.
永利总站ylzz欢迎你_主站轮胎中部早期磨损的解决办法:适当增加轮胎充气量。(不要太高)
The solution to the early wear in the middle of the tire of the full-automatic concrete mixer: appropriately increase the tire inflation. (not too high)
增加轮胎充气量可以减少轮胎与路面的接触面积,从而降低轮胎的滚动阻力,节省燃油。但当充气量过大时,会影响轮胎的减震性能,也会使轮胎变形过大,导致与地面接触面积过小。这样,磨损只能由胎面中部承担,形成早期磨损。所以通货膨胀的幅度应该是适当的。
Increasing tire inflation can reduce the contact area between the tire and the road surface, thus reducing the rolling resistance of the tire and saving fuel. However, when the inflation is too large, the shock absorption performance of the tire will be affected, and the tire will be deformed too much, resulting in too small contact area with the ground. In this way, the wear can only be borne by the middle of the tread, resulting in early wear. So the rate of inflation should be appropriate.
永利总站ylzz欢迎你_主站“啃胎”有几个技巧应对的相关内容就到这里了,您可以参考使用,更多内容就来我们网站www.zkzdsljbc.com咨询吧!
Here are some tips for dealing with "tire gnawing" of automatic concrete mixer truck. You can refer to it. For more information, please visit our website at www.zkzdsljbc Com consulting!
上一篇:搅拌车减速机易损坏部位分析原因
下一篇:新手司机要把握搅拌车与泵车之间的距离
tag:永利总站ylzz欢迎你,永利总站ylzz欢迎你_主站,永利总站ylzz欢迎你_主站
当前位置: 首页 - 新闻资讯 > 行业资讯 >

永利总站ylzz欢迎你“啃胎”有几个技巧应对

作者:中科聚峰永利总站ylzz欢迎你厂家 时间:2022-06-08

“啃胎”是指一个或多个轮胎的内侧或外侧出现异常加速磨损。与其他轮胎相比,一个轮胎的某一部分磨损得很快。在这种情况下不要担心。这里有几个小贴士可以帮助你。
"Tire gnawing" means abnormal accelerated wear on the inside or outside of one or more tires. A part of a tyre wears out faster than other tyres. Don't worry in this case. Here are a few tips to help you.
检查永利总站ylzz欢迎你_主站气压是否过低或轮胎质量是否合格标准。
Check whether the air pressure of the full-automatic concrete mixer is too low or whether the tire quality meets the standard.
检查轮胎轮辋是否不圆,并做动平衡。
Check whether the tire rim is not round and make dynamic balance.
检查前束尺寸,转向杆球头是否松动,转向器固定螺钉是否松动。
Check the toe in size, whether the steering rod ball joint is loose, and whether the steering gear fixing screw is loose.
检查转向轴主轴或承压轴承是否磨损、严重变形或损坏。
Check whether the steering shaft main shaft or pressure bearing is worn, severely deformed or damaged.
后轮胎面不规则磨损。解决方法:检查钢圈、轮毂螺钉、轴头螺钉是否松动。检查制动毂是否不圆。检查弹簧板和弓形夹固定螺钉是否松动。
Irregular wear of rear tire tread. Solution: check whether the steel ring, hub screw and shaft head screw are loose. Check whether the brake hub is not round. Check whether the spring plate and bow clamp fixing screws are loose.

永利总站ylzz欢迎你_主站

经常检查胎压,查看胎面磨损情况。
Check the tire pressure frequently and check the tread wear.
永利总站ylzz欢迎你_主站轮胎中部早期磨损的解决办法:适当增加轮胎充气量。(不要太高)
The solution to the early wear in the middle of the tire of the full-automatic concrete mixer: appropriately increase the tire inflation. (not too high)
增加轮胎充气量可以减少轮胎与路面的接触面积,从而降低轮胎的滚动阻力,节省燃油。但当充气量过大时,会影响轮胎的减震性能,也会使轮胎变形过大,导致与地面接触面积过小。这样,磨损只能由胎面中部承担,形成早期磨损。所以通货膨胀的幅度应该是适当的。
Increasing tire inflation can reduce the contact area between the tire and the road surface, thus reducing the rolling resistance of the tire and saving fuel. However, when the inflation is too large, the shock absorption performance of the tire will be affected, and the tire will be deformed too much, resulting in too small contact area with the ground. In this way, the wear can only be borne by the middle of the tread, resulting in early wear. So the rate of inflation should be appropriate.
永利总站ylzz欢迎你_主站“啃胎”有几个技巧应对的相关内容就到这里了,您可以参考使用,更多内容就来我们网站www.zkzdsljbc.com咨询吧!
Here are some tips for dealing with "tire gnawing" of automatic concrete mixer truck. You can refer to it. For more information, please visit our website at www.zkzdsljbc Com consulting!

截屏,微信识别二维码